Car Overheating and Heater Stopped Working?

If you have to put coolant in it you have a leak somewhere but I would not recommend going back to those guys

1. 2002 mazda 626 heater core?

No, you do not have to remove the dash board at all, on that make and model car it will be located on the passenger side, between the floorboard and the dashboard, or lets say behind the glovebox. It may be enclosed in a plastic case with four screws holding it in place. Remove the four screws, then look under the hood on the passenger side against the firewall (dashboard) about 8 inches down, you will see two black rubber hoses side by side, remove the clamps, then the heater core should be able to be removed with a little push to the inside of the car. To replace it just follow the same instructions in reverse. Thanks for the question. Wish you luck

2. Is a clogged drain the landlord's responsibility?

Yes it is the landlords responsibilities for all repairs to the building... Not caused by tenants... E.g if you smashed a window well that's your fault... Aircon or heater blows up or drains are broken that the landlords responsibility. ...

3. electric heater making a banging noise?

Try turning down the heat and see if that makes a difference. Kind of sounds like water hammer. You may need to get a plummer to look at it and install water hammer arrestors if that is the case.

4. is it cheaper to use the heater or to get a space heater to heat just two rooms?

It's probably cheaper to use a space heater, but it may not be worth it. Space heaters are the cause of many house fires

5. Hot water heater turns off?

If the water heater is older, and you have not flushed it out from the bottom, there could be a sediment buildup in the bottom of the tank that could be shorting out the element. The sediment buildup happens a lot with well water systems. But be careful if you try to flush it out. If if has never been done, there is a chance the bottom valve could break, then all the water will come out! Usually if you flush out about 5 gals, the sediment should flow out. Just a thought!

6. Just replace my heater core ....?

the only ones that you have to bleed has a screw in the neck behind the top radiator hose, just check the coolant in the radiator and make sure it is about half inch from the top , be sure to do this with the engine long as the system is full you should not have any problems

7. What is the difference between a regular water heater and a manufactured home water heater?

liability costs and some manufacturers use more insulation as manufactured homes sometimes require a zero clearance policy

8. Heater core in a 2000 Mazda Protege?

mazda parts are often hard to get and only come from mazda. you can get a used one but then is it worth it? no. For a 2000 protege you should have changed your antifreeze 3 times now. 2002, 2004, 2006. By doing this it keeps it clean and gunk free. Without changing it,this is how you wreck your heatercore

9. Water heater pilot light keeps blowing out?

ALL the newer water heaters are designed to prevent flammable fumes from combusting (outside) of WH. They do this by putting a small vent where the combustable air comes in. I have had to clean that vent on multible heaters. On a. o. smith, on the very bottom of heater, you should have a flexable plastic cover that surrounds bottom (where air comes in) remove and clean. The main vent on this WH is on the insde bottom. You will have to remove burner assy and get small vacuum cleaner to clean. How to trouble this is remove screws from plate where you can see pilot flame (or main flame when burner is on. Pull plate out a little, relite heater and watch and see if it stays lit. If it does, then vent is clogged. You will need to watch it for at least 15 minutes. What happens is the burner uses all the air in the combustion chamber and makes both main burner and pilot go out

추천 기사
How Can I Turn Down the Temperature of My Wwater Heater?
How Can I Turn Down the Temperature of My Wwater Heater?
How can I turn down the temperature of my wwater heater?never heard of a water heater exploding.— — — — — —Water Heater RegulationsThe other pending regulation is on new minimum energy efficiency standards for commercial water heating equipment. As mentioned earlier, that rulemaking was not completed by the end of the Obama Administration, and as a result, is now pending. The issue with that rulemaking is it has a legal deadline by which the DOE has to issue the new final rule on new minimum efficiency standards for commercial water heating equipment by May 2018. Because this rulemaking was not completed, it is not subject to the 60-day freeze in the sense that you are not really freezing anything because they never finished it. "But with the new Administration coming in," says Greene, "there is the prospect that it may say, 'Well we do not really think this is necessary and we are going to attempt to roll it back.'"— — — — — —If the pilot light goes out on your hot water heater is it dangerous or harmfulNo, it is not dangerous. (Unless you are working with a water heater that is 20 years old.) In any modern hot water heater, if the pilot light goes out a fail-safe will go off - preventing gas from leaking out. Also, there is a sensor so if there is not enough air-flow or oxygen with the water heater, it will shut off the gas.— — — — — —How to Install a Gas Water HeaterSome areas require seismic straps to prevent earthquake damage. These straps brace the water tank against the wall to keep the unit from toppling over. If you are not in an earthquake zone, skip ahead to the next step. Seismic straps should be installed approximately 6 inches from the top of the water heater and 18 inches from the bottom. Locate the wall studs closest to the strap measurement and drill pilot holes. Secure one end of the strap to the stud with a socket and ratchet. If block covers the studs, use a masonry bit to create a pilot hole. Wrap the strap around the water heater and adjust the size, securing the adjustable bracket on the opposite side. Pull the strap tight and repeat the process on the lower strap.— — — — — —Tank vs. Tankless Water Heaters?Hello, I think it's no problem to run a 3 zone if the power is large enough. Concerning Tank vs. Tankless Water Heaters, you could find many differences via search through google or yahoo. Do not show here. We are one Chinese Electric Tankless Water Heater Manufacturer. We could supply high quality heater at a reasonable price. More info, please visit the following source.— — — — — —How to Prevent Scale Buildup in a Hot Water Heater Heating ElementWhile there are many things that you can do to prevent scale buildup, one of the most reliable of these is to invest in a water-softening system. This removes the ions dissolved in the water that cause the water to be "hard," calcium and magnesium. A water-softening system must be maintained, as water-softening systems exchange the calcium and magnesium ions for another ion, usually sodium, the sodium ions will run out after a while and need replacement. Because hard water is damaging to pipes and appliances and it inhibits soaps and detergents, however, you may find using such a system worthwhile.— — — — — —The Best Tankless Water Heaters for the HomeHike Crew's portable, propane-powered water heater combines the luxuries of home with the ruggedness of camping. The built-in pump is placed into a water source and attached to a propane tank to provide ongoing hot water for camp showers, washing dishes, and rinsing equipment. Powered by AC/DC electricity, the Hike Crew portable comes with a hand faucet and shower head attachment, as well as some welcome safety features. For example, when the water runs out or reaches 125 degrees Fahrenheit, the unit automatically shuts off the burner. Capable of outputting 1 GPM with 42,000 BTUs, the Hike Crew is not great for all applications, but it's ideal as a mobile unit.— — — — — —What is a good effective heater for large spaces?Convection heaters can heat a whole room more quickly than a radiant heater. That works well if there are a number of people in the room or they are moving about within the room. Some convection heaters also have fans to circulate the air in the room. Convection heaters are inexpensive. You will get one rated up to 5,000 Btu's for less than $50. Like radiant heaters, convection heaters use a variety of heating elements. Ceramic disc heaters cost up to $150 and produce up to 5,000 Btu's per hour. Oil and water filled units are the most efficient convection heaters. They utilize a heating element in a bath of oil or water. Like a water heater, the element cycles on and off. The water or oil stays warm in it's container and heats the surrounding air.
Why Did My Betta Fish Lose All His Color?
Why Did My Betta Fish Lose All His Color?
Dismissing heater, Velvet or old age answers, what came back from Google betta color loss was bacterial, infection. (bloodworms might be the culprit) If bacterial is the reason you will need to decide on an antibiotic. Old school is Kanacyn. Maracyn 2 covers everything as an antibiotic (from what I have read). All I know is stay away from API T.C. Tetracycline, for Betta's anyway. It creates a thick film on top of the water. Not good for our air breathing friends. You clearly care for your Betta. May I suggest knocking off everything except the water conditioner. Caring for our Betta's is really simple: One gallon jugs at water change time water condtioner (my favorite is Prime. 2 drops per gallon) One gallon jug 2 drops Prime treats them fine.1. how do i prevent mold from growing in my car?Everyones answers are pretty good.... For starters ...get a wet/dry shopvac. Just remember to take out the paper filter for wet applications.. Use it to extract as much water as possible... Take out the floor mats and give them a good once over as well. If it's not too cold take a spin on the highway with the windows OPEN... Get some air flow inside the vehicle... You will look crazy but, it will help to dry things out.... Then close the windows and crank up the heat to dry things out further.... If you can use a neighbors or friends garage and see if you can open doors/windows and run some fans in the garage on the car to keep the water evaporating Get a small plug in heater or heat up the garage as much as possible and dry out the car.... Get some DAMP-RID and stow them in the car... good luck2. Cars heater stopped working.?You should check your heater switch3. Water Leaking from Heater Core?need new heater core4. why won't my electrical dryer heat up?Other than a bad heating coil or thermostat, one other thing to check is the fuses (or ciruit breakers). Electric clothes dryers operate on 220V with a fuse on each of the hot 110V leads. If only one of the fuses has blown (a common occurence) the drum will still turn but there will be no power to the heater. Assuming here that you know how to check for a bad thermostat, heater, or fuse/breaker. Otherwise it is time for a 'professional'.5. Heater for my betta fish?Getting a heat lamp (one for reptiles maybe) should be sufficient. Just make sure you regularly check the temperature of the water so you are not overheating your fish6. What Is a Quartz Infrared Heater? | DoItYourself.comA quartz infrared heater is something that you may have never heard about before. Here is a little information to help you learn more about the product if you are considering buying one. A quartz infrared heater looks a lot like a wooden box or an old radio, but just bigger. The wooden box has an opening where the fan blows the heat out of the quartz infrared heater. There is also typically some sort of thermometer and control set on the side of it to allow you to adjust the different settings. Sometimes the heater will come with or you can put on, wheels so that you can move it from room to room in your home. This type of heater is great for giving off the heat exactly when and where you need it. There are infrared heating elements inside of the casing and a fan that helps to circulate and distribute heated air into the room. This product is great, especially if you are not only trying to heat the area, but also keep the circulation moving and humidity level where you want it. It is also environmentally friendly for those who are looking to make a green step in their life.7. Car heater not working?It could be the vent door. you should hear something move when you move th ethermostat form cold to hot or hot to cold if you that you should have a look at that if the problem it wont be very expensive8. Car heater not blowing warm air?check your antifreeze. thermostat or heater core possibly. I had this problem and had to have my heater core replaced
Top 5 Portable Space Heaters
Top 5 Portable Space Heaters
Portable space heaters are a wonderful way to keep a room warm in the winter. They can help turn three season porches into four season porches. Some rooms never seem to get warm even with the furnace off. Portable heaters can help keep these rooms at the desired temperature. Finding the right heater will help keep everyone in the home comfortable all winter long. Below is a list of the based on customer reviews:5. Dayton 3VU33 Space Heater The Dayton 3VU33 Space Heater is one of the most convenient portable space heaters. It uses a long 72 inch cord that allows it to be placed anywhere in a room. This heater can be moved from room to room using the built in handles. It can be set on top of any hard surface and the feet will keep the base off the ground. The Dayton is built with quality. It is constructed out of a steel frame. Even the intake and discharge grilles are made of steel. This heater will last for a long time. It also contains many safety features. It will turn off when it gets overheated and will automatically shut off when it is tipped over. It can easily be reset using the thermal switch. The temperature can be set using the dial on the front of the heater. When the heater is turned on and working, a power indicator light will shine. The Dayton 3VU33 Space heater is a quality portable space heater that is perfect for any home.Dayton 1VNW9 Electric Heater, Analog Ceramic, 1500 WAmazon Price: $56.81 Buy Now(price as of Oct 19, 2013)4. Soleus Air Oscillating Reflective Heater The Soleus Air Oscillating Reflective Heater offers many options, which are uncommon in most portable space heaters. This oscillating heater warms the room by heating surfaces first - just like the sun. This produces a powerful heat that can warm a room of just about any size. It does not deplete oxygen in the air, which makes it a much healthier way to heat a room. There are no fans to draw up dust. The Soleus Air contains many safety features. This heater has tip-over protection and will shut off if it overheats. It contains a timer that will turn it off after a set amount of time. The timer can go up to seven and a half hours. A remote control is included with the Soleus along with a telescoping stand. The Soleus Air Oscillating Reflective Heater is one of the healthiest portable electric heaters for sale.Soleus Air HR1-08R-21 Oscillating Reflective Heater, Silver, BlackAmazon Price: $79.99 Buy Now(price as of Oct 19, 2013)3. Lasko 754200 Ceramic Heater The Lasko 754200 Ceramic Heater is the perfect portable space heater for a home or office. It can operate on a 1500-watt setting, a 900-watt setting and a cooling fan setting. The fan setting is perfect for hot summer days. It is extremely quiet which is perfect for use in an office, library or museum. It is small enough to be placed under a desk to keep the legs warm or it can be set up on a shelf. The Lasko can be moved around using the carrying handle. This heater is extremely easy to clean. A vacuum brush attachment can be used to clean the dirt, dust and lint from the grill. The heater should be dusted regularly with a soft cloth. The Lasko 754200 Ceramic Heater includes a three year limited warranty that will provide peace of mind. This Lasko heater is a quality long-lasting portable space heater.Lasko 754200 Ceramic Heater with Adjustable ThermostatAmazon Price: $29.99 $24.00 Buy Now(price as of Oct 19, 2013)2. Sunpentown SPT SH-1507 Mini-Tower Ceramic Heater The Supentown SPT Sh-1507 Mini-Tower Ceramic Heater is one of the more affordable portable space heaters. It can be found at many retailers for less than fifty dollars. The Supentown is small enough to fit into the tiniest of rooms. It will match any décor with its slick fancy design. Not only does it look great but it also has many features. It uses energy-efficient ceramic to heat the air. It slowly heats the room by rotating in an oscillating pattern. The three heat settings include a 600-watt low setting, a 1200-watt high setting and a fan only setting to cool the room in the summer. The included filter is washable. The heater can be transported from room to room using the carrying handle. The power indicator light will show that the heater is on and is working. The thermal cut-off switch will turn the heater off when it gets too hot and the tip-over switch will turn the heater off if it is tipped over. The Supentown SPT SH-1507 Mini-Tower Ceramic Heater is the perfect portable space heater for a child's bedroom or a nursery.Sunpentown SPT SH-1507 Mini-Tower Ceramic HeaterAmazon Price: $69.99 Too low to display Buy Now(price as of Oct 19, 2013)1. Mr. Heater F232000 MH9BX Buddy Indoor-Safe Portable Radiant Heater The Mr. Heater F232000 MH9BX Buddy Indoor-Safe Portable Radiant Heater is a high quality portable heater that can handle any type of abuse. It can heat any space that is less than 200 square feet. It is perfect for outdoors or at construction sites as it can handle the elements and it does not need an electric power source. It runs on propane and can be easily connected to a propane tank as small as one pound and it can be hooked up to a propane tank as large as twenty pounds. Mr. Heater is the perfect heater for when the power goes out. It is started by using a push knob to ignite the pilot light. The pilot light will extinguish if the heater is tipped over or if the oxygen levels drop significantly in a room. Always use a carbon monoxide detector when using this heater indoors. A fold-down carrying handle makes it easy to transport the Mr. Heater. The Mr. Heater F232000 MH9BX Buddy Indoor-Safe Portable Radiant Heater is one of the best portable space heaters for outdoor camping.Mr. Heater F232000 MH9BX Buddy 4,000-9,000-BTU Indoor-Safe Portable Radiant HeaterAmazon Price: $144.40 $74.99 Buy Now(price as of Oct 19, 2013)A portable heater can keep even the largest rooms warm. Make sure the heater will provide enough heat for the room that it will be used it otherwise the entire room may not get warm. It may be a good idea to purchase two or more portable space heaters to help heat the space.
Why Hot Water Heater Keeps Going on and Off?
What brand ? It should be under warrintee1. Can I install a hot water heater myself?This is not a difficult project to do on your own. If you were happy with the previous performance you can stay with the same specifications as the old one. Just make sure the power is not turned on to the new water heater until the tank is full of water or you will burn out the new heating elements.2. why is my water heater making a click sound?Generally, this problems not occur in water heating. If this sound noise again and again then possibilities of short circuit. Call any service center and repair it3. Im wanting to buy a tankless water heater?they do not make a large enough one for you4. water heater not heating what's wrong?JEFF's answer is a possibility but it could also be the thermostat and/or the gas valve. As JEFF said the thermocouple/thermopile may be defective but on some gas valves if the thermocouple/thermopile is defective it will shut off the pilot light. If the thermostat is defective, it will not send a signal to the gas valve to turn on the main gas. If the gas valve is defective, it will not open to supply the main burner to heat the water. Get a reputable qualified gas fitter to check your hot water controls out and repair what ever is required. Do NOT attempt to do this yourself.5. If I close the valve on my hot water heater going up to my house will it hurt my hot water heater?If you let the water get low in the heater, then that will damage the elements. But it will not give you water without the pressure of turning it on6. Can hot watter be put into a hot water heater at the normal water input to keep the water heater from runnign?It would probably work, but unless somebody is using the hot water, do not you think the water just sitting in the tank would cool down causing the heater to come on anyway. The only time water comes into the tank is when water goes out of the tank. Would not it make more sense to run your hot water through the hot water pipes and put a thermal switch on the water tank? You may also have to install a pressure regulator in the line somewhereincase the water get's too hot and builds too much pressure.7. will any similar water heater gas valve work?you can type in robert shaw customer service and ask them. gas valves do not fail very often so i would check the lines for obstructions and make sure that's the problem, and you could nearly buy a new heater for what a new valve will cost. make sure the regulators [on the tank and one on the house] are good if you have them. sometimes the regulators will freeze especially if they are bad and leaking8. Why is my hot water heater not working?the user-friendly answer is "confident". Now the "howevers". you could pass with organic gas or electric which means you could desire to have adequate means for the chosen type to make it artwork. direction electric service can often be upgraded if inadequate, and organic gas can often be dropped at the place of abode in case you have not any longer have been given it presently. different than that i would assume which you would be able to desire to get a tankless setting up. As yet another man or woman mentioned, before doing that i think of i would inspect why you are having issues9. for hair loss electric water heater,is the reason?I am not sure that someone with your level of understanding should be using anything electric. And perhaps not even a bucket.10. how do you light a hot water heater?Turn off the gas to start.turn the pilot control to the off position for a few minutes.Then to start turn the gas valve to the on /flow with the line position,and turn the pilot dial to the pilot position and hold down and add flame to the burner/thermocouple while holding the pilot button down for approx. 30 seconds till when you let the pilot button up after 30 seconds, it stays lit Repeat this procedure untill it stays lit,or call in the GAS CO. they are super helpfull.
My GE Smart Gas Water Heater Was Leaking From the PRV. My Husband Replaced and It Is still Leaking.?
I agree with above answers 1,3,4 Make sure valve is seated by giving it a quick pop at the relieve lever. If not try what 1,3,4 said.1. Gas Water Heater Issues. Water is too hot?Sounds like one of your thermostats is messing up. Dial your thermostats back some more and see if that does the trick. PS. It has nothing to do with your thermocouples2. How do i re-turn on gas to water heater?you need to keep the gas valve depressed for several minutes(which can seem an eternity)3. Gas Water Heater pilot light does not stay lit. Gas is On. Any Ideas Why?you likely need a new thermocoupling - plumber They are easy to replace unless you have one of those new water heaters with the enclosed burners, but it can still be done. Turn the gas valve off until you figure out for sure what the problem is. Word to the wise.4. Gas Water Heater Pilot Goes Out Every Morning?Replace the thermocouple just for good measure, Clean the pilot assy. -- could be partially gunked up with sulfur deposits blocking the full flow of gas getting through. Make sure the tip of the thermocouple is in the flame, and you got a good pilot. Check around for "Air drafts" blowing the pilot out --install a "hood" on your vent pipe on the roof. Consider a new tank if these measures fail--the pilot assy if plugged can cost $35-50--the gas thermostat(side of tank)could be going out--$75-100. A new tank bought at a lumber/hardware store >> low end about $300 and up for better models.5. how do you replace a gas water heater?No, no fuse. Need to check and see if pilot light is lit, that is likely the problem. When hot water heaters fail and need to be replaced, it usually due to a leak6. Can you switch a hydro heat system to a regular gas water heater & pump?It should not be a problem converting the system over to a gas storage tank type hot water system. but do you really need a circulation pump for the system ? a heat pump is for a domestic heating system. the only use on a hot water tank is to keep the water in the lines hot when the faucet is open. the cost is according to the size tank you will need for the unit it is being used for7. Gas water heater not working correctly, and I know nothing about gas heaters - help please!?Sounds like to me the gas valve is bad. Call the landlord to have fixed or if water htr is too old they should replace it8. Natural Gas water heater safety designsThanks for the input, we figured this one out. Because we could not find a leak in the tank and the T&P valve was not leaking we were a little baffled. When this unit was installed it was so tall we had to actually dig a hole in the crawl space about 1' deep. This hole was filling up with water. Since we are in a group of 5 townhomes we figured out the water was come from 3 homes away due to a broken water line, thus filling up the hole our water heater is in to the point it would prevent enough oxygen to keep the pilot and burner from working. This is one of those crazy things that makes you think outside of the box9. Proximity between electrical and gas water heater not met.?Most likely since the water heater being moved causes this to no longer meets code it most likely had to have a permit pulled and be inspected by local officials. I believe Ontario's rules are similar to North Carolina's which require the contractor to install any work according to local codes to be approved by the inspector. If indeed they did fail the inspection it is the utility companies responsibility to make the changes needed to meet local codes. I hope this helps.10. Gas water heater pilot light won't stay lit. Any advice?Sounds like your pilot light may need cleanig . IF you can reach with a small steel brush or steel wool, give it a good brushing,rubbing, but be fairly gentle as not to bend it ... Other than that, Sorry
It's August. so Why Is Your Office Freezing?
For many women, here's what summer "business casual" looks like: a dress or a skirt and blouse, plus a thick sweater, wool blanket for the legs, and sometimes even a space heater to stick under your desk.Yes, judging by the temperatures in some corporate offices, you'd think humans weren't capable of surviving outside a meat locker. As soon as the temperatures rise outside, they drop inside. I've been in offices going through major rounds of cost-cutting -- like rationing office supplies and dropping carrots from the salad bar -- but the AC is still cranked to a level that implies management likes to set fire to $100 bills.Why is that? I have long assumed it's a vestige of patriarchy. Corporate office temperatures are set to be comfortable to slightly heavy-set men in suits. If you're wearing three layers up top (T-shirt, dress shirt, jacket) and wool pants and socks, then I can see how a temperature in the low 60s might be necessary to avoid any sweat whatsoever. The fact that such temperatures will feel cold to a woman wearing a skirt (even with nylons) is just not considered relevant to serious business -- much like discussions of telecommuting or flexible hours or other such touchy-feely concepts.But in an era when we are becoming more and more concerned about the environmental impact of our decisions, near-freezing office temperatures are a huge waste on many levels. And it turns out that even the most formal cultures can change if they want. Trending News Acosta Resigns "Trauma" Of Family Separation Mueller Testimony WATCH: R. Kelly Arrested At least that's the lesson I'm taking from Japan where, after the March earthquake and tsunami, the country is operating with a lot less power capacity than it had last year. Japanese citizens have headed off rolling blackouts by conserving -- a big part of which has been raising the temperature in frosty offices. Japanese executives have learned that you can conduct business in short sleeve shirts and khakis. Casual, heat-beating work clothes have become (literally) cool.There's no reason we can't behave the same way. I'm not saying don't turn on the AC at all. But a temperature in the high 70s is perfectly reasonable when it's 90 degrees outside. There's no reason to make your employees pack mittens in their purses.What's the temperature in your office?Related:Can You Become a Morning Person?Working Parents Have Plenty of Free Time What Would You Do If You Couldn't Be Fired?Photo courtesy flickr user, Caza_No_7
'Stand by Your Pan' to Avoid Kitchen Fires, Expert Says
CNN -- A pan left unattended on the stove, a forgotten cigarette or a space heater left too close to the drapes -- each is a potential ingredient for one of the more than 380,000 home fires that occur in the United States each year, leading to approximately 3,000 deaths. The first step in decreasing your risk of injury is prevention, and according to Meri-K Appy, president of the Home Safety Council, a national organization dedicated to preventing accidental home injuries. With a play on the words of Tammy Wynette, Appy recommends that you "stand by your pan," to prevent the No. 1 cause of home fires: unattended cooking. (Watch tips from fire fighting pros -- 5:30 )Stay close to anything you're cooking on the stovetop, she said. Have a lid for the pan right next to you so you can slide it over the pan if the contents catch fire -- and once the lid is on, don't peek.The leading cause of fatal fires in the home has consistently been smoking-related. "If you have a smoker in your home, you have to help that person pay constant attention," Appy said. "Ideally, encourage the person to quit. Among all the health benefits, smoke-free is also fire-safe." If quitting isn't on the smoker's agenda, she recommends encouraging that person to smoke outside and use a deep, sturdy ashtray, since "cigarette or smoking-related fires tend to involve a lit or smoldering cigarette and upholstered furniture." If someone is smoking inside the home, again use a deep, sturdy ashtray on a sturdy table and douse butts with water before you throw them away.That sounds like common sense, but a forgotten cigarette butt can smolder for hours, Appy said. By the time a fire starts, the smoker could be asleep in another room, leaving the fire undiscovered until it is well under way.Appy also encourages homeowners to take time to have central heating equipment and chimneys serviced every year, This step will help protect you from fire hazards as well as exposure to carbon monoxide. And she warned to take special care when using portable space heaters. If they're too close to drapes, people or pets, fires or burns may result. "So let's say that a fire does happen, well now you want to know about it immediately," Appy said. And the early warning from a system of interconnected smoke alarms may give you precious time in a fire. Interconnected smoke alarms are required in new home construction. They can be installed in an existing home by an electrician, or a wireless alarm system can be easily installed. Appy recommends at least one smoke alarm on every level of a home. Additional smoke alarms should be placed inside bedrooms.Beyond early warning, it's important to have an escape plan with which all the members of your household are familiar. It should include who will help whom in getting out of the house. Once the plan is in place, you'll want to practice it with your children. Make sure the children know at least two ways to get out of every room. "You don't have to scare the kids to death, but the idea is that you're going to choose a way out that doesn't have very much smoke," Appy said. If there are children in the home, Appy recommends keeping an escape ladder in their room, since you'll want to help them get out of the house.Appy's prescription for the most peace of mind is to have a fire sprinkler system. "They're very brilliantly designed to activate when the fire is still small," she said. And, contrary to popular belief, sprinkler systems are activated by heat, rather than smoke, so the smoke from that burnt toast won't mean a soggy mess in your gives you the latest stories and video from the around the world, with in-depth coverage of U.S. news, politics, entertainment, health, crime, tech and more.Unattended cooking is the leading cause of home fires in the Unted States.
Water Heaters
googletag.display("div-ad-articleLeader");Safety Points When Repairing Or Replacing Any Water HeaterFollow Carefully To Avoid Injury Or Property DamageAll present a need to use extreme caution when servicing. Some types of need attention in areas that  others may not. These are common safety precautions that must be taken broken down by the various models out there. Gas ;Gas  have  a few things that are unique to this type of unit. First and foremost when working on a gas water heater is to make sure you've positively shut off the gas to the appliance. This is usually done right at the meter. There are some that will have a gas shutoff right at the unit and this is also an acceptable place to close the gas supply. Propane as well as natural gas units follow the same safety rules.Secondly some gas have an electrical connection as well as the gas hookup. This will be to power a draft inducer or power vent. It can also be for electronic ignition systems. All power  supplies should be shut off, prior to performing any service work. This can be done at the electric panel by locating and shutting off the proper circuit breaker. It can also be done at the unit if an emergency on off switch is available. Either way it's recommended that an electrical meter be used to check and make sure there is no power present before servicing. Electric ;Electric will require the same precautions.  All electricity to the unit must be shut off and proven to be shut off with the use of an electrical volt meter. Most electric use 220 volts. There should be no power present whatsoever. Use caution and make sure a volt meter is used to be sure the power is off. Some units wired for off-peak savings can bring power from several sources. This is the reason that testing is so important. Oil Fired ;Oil fired have a supply line coming from a remote  oil storage tank. This line brings fuel oil to the burner. A shutoff valve should be in line, usually at the oil tank. Close this valve to positively shut off the oil supply.There will be a fire-o-matic valve in line, at the burner of the oil-fired water heater. This valve uses a spring-loaded action to shut off the oil supply in case of fire. The round handle on top will be reverse threads. On this valve the rotation of the handle to close it will always be counterclockwise. Unscrewing this valve handle until the top comes right off will assure the valve is off. You should feel the valve stem depressing as the handle is turned. If you don't tap the valve to un-stick the mechanism inside.Oil fired also use electricity to run. This should be shut off either at the electrical panel by locating and turning off the proper breaker, or at the emergency switch at the burner. Once again a volt meter is recommended to make sure there is no power to the unit. Common Safety Issues For All Types Of All types of present a common reason to use extreme caution when repairing or replacing any components. The water inside is extremely hot and it's recommended that all units be allowed to completely cool before attempting any servicing.This type of apparatus now comes in models that are super insulated and it can take literally days for the water heater to cool down. This is due to the minimal heat loss. The process can be expedited by running the hot water in the home after the water heater has been disabled. This will push out any remaining heated water and replace it with cool water from the your water main, or well. Allowing you to safely drain the unit for repairs or replacement.How to Clean and Service an Oil BurnerAmazon Price: Buy Now(price as of Oct 13, 2013)Repairing Or Replacing An Oil Fired Water HeaterNot a job for the weak at heartWhen your repairing an oil-fired water heater, many times the problem will lie in the burner not firing when it's called. This can be due to several causes. First and foremost is there fuel in the oil tank Once it's established that your oil burner is getting fuel, the next thing to check is the emergency switch. There are normally two. One will be located at the burner appliance and the other is usually upstairs outside of the basement door.Many times one of these switches has been inadvertently turned off. Believe it or not this happens often. Having a breakdown be this easy to fix usually isn't so common.The next thing we'll look at is what's known as a "cad cell". This is a photo sensitive eye that acts as a watchdog for the flame in the burner. If the unit starts and a flame is not seen by this component within 60 seconds, the photo cell which is wired in line will disable the burner to keep the pump from running when the oil burner has failed to fire.This cad cell is located under the transformer on most oil burners. There are two hold down screws between the transformer and the burner appliance. These are loosened with a proper sized nut driver and the transformer can then be tipped open. Inside the small cad cell plugs into socket.Remove the cad cell init and wipe it clean with a damp paper towel. Notice any black residue that shows up on the white paper towel. This will fool the eye into believing there is no flame. Once you have cleaned the cad cell re-insert it into the socket from which it came. Close the transformer cover and retry your system.This will take resetting the primary controller on top of the burner. There is normally a red button to hold down for resetting. If the hold down button doesn't reset then you most likely have a bad control and this will need to be replaced.Another reason for an oil burner to fail is a clogged oil filter. This piece of equipment is usually right after the oil tank. There should be a valve to shut off the tank. Once the tank valve is closed the oil filter can be disassembled and a new cartridge can be installed. Re-fire the system and see if this solves the problem.One other issue that can happen when oil tanks are outside. Cold temperatures can cause heating oil to solidify. The pump will lose the ability to move the thicker oil. For cold climate conditions with out door tanks a mixture or blend as it's called must be used to prevent freezing.Many oil fired  have power venter's today. Some will have a draft inducer. Both perform the same function. They remove the toxic waste fumes from an oil burner to a remote location outside where they will disperse harmlessly.When a power venter fails it can be because of a leak in the flue piping or a bad motor. It can also be the controls that run the unit. There are also spill switches that sense temperature. These should be checked for failure as some are reset-able.Replacing an oil fired water heater will mean disconnecting your oil line after shutting it off of course. All electrical connections and following the water pipe instructions later in this article, which are common to all types of .Repairing Or Replacing A Gas Fired Water HeaterFirst and foremost when dealing with gas-fired hot is to be sure it's legal within your jurisdiction to work on your own unit. Some gas codes won't allow anyone but a fully licensed plumber or gasfitter to touch anything gas related in their areas.If you find that working on your own gas equipment is legal then please follow all the safety precautions previously discussed. Gas can be deadly improperly handled. severe property damage and personal injury is possible.That being said,  here are a few things that the average homeowner can carry out easily when it come to gas water heater repair. One of these will be a thermocoupling replacement. This will have the symptom of your pilot light continuously going out and not staying lit when you try to restart it. There is a metal probe that sticks right into the pilot flame on standing pilot type gas-fired hot . This probe is heat sensitive and allows the main burners to run if it senses heat from the pilot. When the heat is interrupted the pilot will be shut down and the main burners will not open. This is a safety feature to keep your basement from filling up with gas when the burner hasn't been ignited ny the pilot flame.When the pilot goes out you can try to re-light it. Sometimes just a fluke, it does happen. A backdraft down the chimney or in the room when an exterior door is opened can blow out a weak pilot flame. Re-lighting and preventing the draft from re-offending is the solution.If the pilot lights but won't stay lit then most likely there is a bad thermocoupling. This is a copper or aluminum wire that runs from the flame probe, up and into the gas valve. They come in various lengths and models to match the one your replacing. There are small nuts on both ends and several screws are normally holding the assembly into the burner area. Remove the unit and replace with the same model and length. These are available at your local plumbing supply house. You'll need the old part to match up.installation is the reverse of removal and once the part is reinstalled you must test the line either with compressed air or by turning on the gas and spraying the connections with a soapy water solution. Watch for any bubbling. None is exceptable as gas piping must be 100 percent leak proof to be safe.Once you have determined there are no leaks present you can go ahead and try out the repair. Restart the water heater and relight the pilot according to the directions that will be on the unit. If this repair doesn't solve the problem then next is the gas valve. All gas valves are not created equal and the one you have must be replaced with the same make and model number. This task is usual;ly not taken on because the cost of labor and materials almost doesn';t make sense when new units are available for almost the same cost.Follow the instructions for the water line part of gas water heater replacement, later in this article. These instructions will be all the same for all types of hot . The gas part will consist of only disconnecting the gas line once the gas has been turned off., and reconnecting it once your done.Water Piping Portion Of Repairing Or Replacing A Water HeaterOne size instruction sheet will fit allIssues that can cause a hot water heater failure are often attributed to a continued leak in the water lines. If a small amount of water constantly drips from a leak anywhere in the system, there will be a significant increase in the amount of harmful minerals and iron that will decrease the lifespan of all types of .Whether you burn oil or gas or even when an electric water heater is being used. All leaks no matter how small should be repaired immediately upon discovery. This will assure you the most longevity you can get from your Water heater.When a leak is discovered the first thing that must be done is to shut off the water prior to the leak. Use the closest shutoff you can find to the repair area working towards the water main. Once you find a valve, close it to isolate the water heater from the water supply.Make sure you have read and followed the shutoff and safety procedures and cautions above. If you have then all power and fuel sources should be verified off at this point. Find the boiler drain at the bottom of your water heater. Usually right in plain sight. Occasionally you will need to remove the lower cover from the bottom of the water heater to get access to this valve. It will be a simple faucet that allows a hose connection to be made.Be sure to run your drain hose outside somewhere safe, or to a plumbing drain if you have one low enough. Next you'll hook the hose to the boiler drain and open the valve.  You will need to go into the home and open all hot water faucets. This will allow air to be pulled into the pipes as the water drains out below. continue draining until the water heater is completely drained.If your leak is on a threaded fitting, you'll need to back up to the nearest union or threaded coupling that can be taken apart. If this threaded union doesn't exist then the pipe must be cut to make the repair.TIP; On rare occasions if the right conditions exist, a large pipe wrench can be used to turn a threaded nipple into the fitting it's leaking from, about a half revolution. Put pipe thread compound up against the fitting and completely cover the threads that are entering the fitting. The goal is to decrease the possibility of a leak. Keep in mind you'll be unwinding it from the fitting on the other end. If you try to over-do this tip, your likely to cause another leak.Leaking copper lines can be cut, and couplings with new pipe installed to make the repairs. This will also be the procedure for replacing a water heater as well. Use a tubing cutter and remove the leaking pipe section. match up the size of the piece you cut out and then follow these instructions on how to solder copper tubing.When replacing any water heater you'll simply follow the instructions for each type of water heater above to shut down the unit and then disconnect all connections.This will include your fuel source, after making positively sure it's one hundred percent off at the source. Your water main is off and all lines have been drained before you begin.You have accounted for and acquired all the necessary parts to replace any components that are needed and you have the new water heater on site and ready to go.You have checked to make sure it is legal for you to work on your own water heater in the part of the country you live in.Once these requirements have all been addressed you can safely make all the cuts and disconnect the old water heater. Remove electrical wiring from any electric models and tag the wires. Note colors and the color of the wire it was connected to if different.Move your old unit from your path, and place the new water heater in it's place. Try to line up any hard threaded pipes such as gas piping with a priority because these are the hardest to alter for configuration. Copper lines can be re-routed if need be.Tie back in any flue pipes next, as these are also more difficult to work with then simple copper tubing. Last but not least, tie in your water lines and solder it all up. Test the water lines by shutting off all the faucets that you opened upstairs and turning on the water slowly.If there's a leak you'll hear air being pushed out of the leak, before the water gets there. This gives you a chance to fix any solder leaks before you get the system wet. It can save a lot of time filling the system with this slow fill method.Once you have the water lines tight you can test your fuel connections. Oil leaks will simply be visible as a mess on the floor. Gas pipes should be tested with a soapy water spray solution on the joints. If there's a leak the soap will bubble up.Turning on the power to the electric water heater will be the test. If the breaker pops then you miss wired the new connections. Check your notes and the water heater instructions and if still in need of answers call a qualified electrician.Once you have finished testing your job you can place the new water heater on-line and see how the job went. Give your new water heater the proper amount of time to heat up and test the water at your kitchen sink.The normal range for domestic to make your hot water would be between 110 and 120 degrees farenheit. This will of course be set to personal preference once you've allowed the unit to get to temp. Re-adjust up or down in slight intervals until your completely satisfied with your functionality.Conventional Electric Water HeaterLess efficient than a Tank-less unitCredit: DreamakerConventional Gas Water HeaterCredit: DreamakerRheem 22V40F1 Natural Gas Water Heater, 40 GallonAmazon Price: $452.00 $352.19 Buy Now(price as of Oct 13, 2013)Rheem 42VR40-40F High Efficiency Natural Gas Water Heater, 40 GallonAmazon Price: $1,268.00 $387.89 Buy Now(price as of Oct 13, 2013)function articleAdMiddleLoad()if (typeof jQuery != "undefined") var lastPosition = 0;var minimumDistanceBetweenAds = 1200;var minimumDistanceFromBottom = 300;var adsToPlace = 20;for(var i = 1; i 0// element is after last placed ad&& !$(this).hasClass("articleAdMiddle")// element is not an ad&& ($(this).position().top - lastPosition > minimumDistanceBetweenAds // enough space between ads&& $(".articleText").height() - $(this).position().top > minimumDistanceFromBottom// enough space from the bottom of the article|| $(this).prev().hasClass("articleSlideshow") // previous element is a slideshow))$(this).before($("#articleAdMiddle" i));googletag.display("div-ad-articleMiddle" i);lastPosition = $(this).position().top;spotFound = true;return false;);// If no spot can be found, stop the loop and remove any remaining banner slots.if(!spotFound)for(var j = i; j
What to Do About This Potential Mold Issue?
Mold can be tricky. Bleach does not kill mold. It only "bleaches" it. Only certain EPA approved products can eradicate mold. I would look for a leak...roof leak, water heater, bathroom tub....or lack of insulation resulting in condensation like a non-vented bathroom fan. Home depot has a nice rent-able spray system to remove and kill mold or you can call a licensed/certified remodeler who has specialty equipment to remove the mold and you can finish up the remodeling yourself. My main point is to get an expert if you can not find the source of the previous mold/leak or feel overwhelmed using EPA approved mold killer and then remodeling as normal. Mold esp "Black Mold" can be deadly so a few simple store bought HD/Lowes. mold detection tests can give you some peace of mind expert is usually better but start out simple...... Best of luck and let us know how you do...1. Which Hot Water Heater is good for us?That many residents and bathrooms pretty much demands you stick with the large gas heater. Gas water heaters recover faster than electric ones; a larger heater can deliver a larger, longer surge of hot water if more than one shower is going at the same time, and the gas heater can sort of keep up with the heating requirements of a couple of showers going simultaneously. All other factors being equal, find a water heater with the highest burner capacity. That can better keep up with the ongoing flow and behave, kinda, as a "tankless" to heat water as it's used. After that, find one with the longest warranty you can afford. Gas heaters die younger than electrics, generally. There's more surface area and more localized heating, which stresses the enamel lining inside, causes it to crack, and then the steel rusts and fails. If you can periodically replace the anode rod, that will essentially reset the corrosion clock inside the heater, as the anode rod corrodes first. Putting in a new one can keep the heater going way beyond the warranty period. The downside there is it's hard to find replacement anode rods, and they are damned hard to remove. You need a wrench as long as your leg. If you replace one grease its threads first, so you can get it out again later. After that, do whatever you can to minimize heat loss. Add insulation. Be careful not to block off flue exits or air intakes, of course. Add plenty of insulation to the hot pipes, too. The less heat lost from the tank to the fixture, the more heat makes it to the fixture and maybe you can turn the hot water down a bit at the fixture. Consider adding insulation to the exhaust flue, too. If it runs any distance inside the building, insulating it is a good thing to do: less waste heat inside that air conditioning has to remove, and less condensation inside too, condensation that is slightly acidic. Get it all out and gone. After that, consider adding a timer. Most gas water heaters, though gas, still have an electric plug to run the thermostats and ignition. You can put that plug on a timer and simply have the heater turn off during the night, when you are not using it. Have it come on again about thirty minutes before people start getting up and there will be plenty of hot water for morning showers and whatnot. Off again during the day while everyone's at work. Do not listen to people telling you you wo not save money by putting the thing on a timer. I actually PUT my water heater on a timer, and it made an immediate and noticeable dent in my utility bill. It WORKED. But I had done all that other stuff, first, to minimize how much heat had to be made up after down periods. Good luck with it.2. How Hot Should Water Heater Be?130 anything lower you risk long recovery time 130 is the highest you can go without risking being scalded. BTW Both t-stats should be the same temp3. rats or hot water heater noises? puzzled.?It sounds like the expansion and contraction of the pipes and heating duct surfaces. You really need to relax. I live in an old house and it makes all kinds of noises. Try putting on the tv or a mellow radio station or a fan as white noise and do not worry about the normal noises of living. If you see a rodent then that is one thing but do not freak about stuff that's not that big of a deal. Relax
데이터 없음

Copyright © 2020  Shandong Abusair Agricultural Machinery Co,. Ltd- |  Sitemap

Multifunctional farm Abusair machinery  |  Tea Professional Cultivator farm machinery